Small Hybrid Injection Molding Machine
PNX-III Series
Clamping force:
41~65ton (45~72USton)
Hybrid
Direct
TACT IV
INQUIRY & QUOTATION
MODELS & SPECS
"X-Pump®" was invented with NISSEI's pioneering spirit...
These "X-Pump®" equipped PNX-III machines redefine the concept of injection molding!
It is a fusion of hydraulic control and servomotor technology!
In spite of the rising popularity of electric injection molding machines in today's industry, NISSEI's original hybrid pump-equipped (X-Pump ) PNX-Ⅲ and FNX-Ⅲ series were created by combining the advantages of both hydraulic and electric type machines. It offers outstanding well-balanced performance, enabling it to do a wide variety of molding from precision/thin-wall to thick-wall products. NISSEI hybrid type injection molding machines inherit the combination of hydraulic advantages (high-durability, low initial cost, low maintenance cost, and high-load injection capability), direct pressure clamping advantages (initial mold open linearity, contact pressure uniformity, and long stroke), and electric servomotor advantages (energy efficiency, high repeatability, high response, and low noise).
It redefines the concept of hydraulic injection molding systems.
Comparison of power consumption
(Comparison with other NISSEI machines)
Characteristics of X-Pump® Hybrid Machines
* Actual power consumption may vary depending on molding conditions, etc.
Fusion of Hydraulic Control and Servomotor Drive Technologies
Intelligent Hybrid X-Pump® System
The X-Pump System combines years of accumulated expertise in hydraulic and state-of-the-art servomotor drive technologies. Since the servomotor rotates at the required speed only when necessary, the extremely efficient X-Pump achieves drastic energy-savings. Furthermore, with exceptional stability in injection repeatability and controllability in low velocity/pressure range, it makes production of higher-precision and higher-quality molded products possible.
High-Performance & High-Functioning Controller TACT® IV
Larger screen, newly designed operation panel, and convenient & user-friendly premium software are equipped to improve workability & operability, and the quality & production management functions have been reinforced.
Sheet switch type is used for the operation panel, and 15-inch vertical LCD can arrange two windows vertically, materializing superior visibility and operability.
Molding condition settings to increase yield, which used to require a skilled technician, are automated and simplified. Its "Easy Setting" permits the reduction of defect rate.
In addition, new features, such as SET-UP screen and display of the descriptions of adjusters, allow saving of preparation time from mold installation to starting of mass production and materialization of easy & reliable operation.
PNX40III
PNX60III
Item
Unit
2A
5A (std)
Screw diameter
inch
(mm)
A
0.63
(16)
B
0.75
(19)
A
0.87
(22)
B
1.02
(26)
BB
1.10
(28)
Injection capacity
inch3
(cm3)
(oz)
0.79
(13)
(0.44)
1.1
(18)
(0.6)
2.1
(35)
(1.2)
3.0
(49)
(1.6)
3.5
(57)
(1.9)
Max. injection pressure
psi
(MPa)
(kgf/cm2)
39820
(274)
(2800)
30930
(213)
(2175)
40100
(276)
(2820)
30290
(209)
(2130)
26170
(180)
(1840)
Clamping force
USton
(kN)
(tf)
45
(405)
(41)
Clamping stroke
inch
(mm)
11.8
(300)
Min. mold thickness
inch
(mm)
6.7
(170)
Max. daylight opening
inch
(mm)
18.5
(470)
Tie bar clearance (H×V)
inch
(mm)
12.2x12.2
(310x310)
Die plate dimensions (H×V)
inch
(mm)
17.7x17.7
(450x450)
Ejector stroke
inch
(mm)
2.4
(60)
● All specs and dimensions are subject to change without notice or may differ depending on export destinations and manufactured year.
● NISSEI is not responsible for any inaccuracies contained herein.
● Please consult our sales representative or NISSEI regional offices before designing a mold.
● Actual plasticizing capacity may vary, depending on the molding conditions and material used.
Item
Unit
5A (std)
Screw diameter
inch
(mm)
A
0.87
(22)
B
1.02
(26)
BB
1.10
(28)
Injection capacity
inch3
(cm3)
(oz)
2.1
(35)
(1.2)
3.0
(49)
(1.6)
3.5
(57)
(1.9)
Max. injection pressure
psi
(MPa)
(kgf/cm2)
40100
(276)
(2820)
30290
(209)
(2130)
26170
(180)
(1840)
Clamping force
USton
(kN)
(tf)
72
(641)
(65)
Clamping stroke
inch
(mm)
16.9
(430)
Min. mold thickness
inch
(mm)
6.7
(170)
Max. daylight opening
inch
(mm)
23.6
(600)
Tie bar clearance (H×V)
inch
(mm)
12.8x12.8
(325x325)
Die plate dimensions (H×V)
inch
(mm)
18.8x18.8
(478x478)
Ejector stroke
inch
(mm)
2.8
(70)
● All specs and dimensions are subject to change without notice or may differ depending on export destinations and manufactured year.
● NISSEI is not responsible for any inaccuracies contained herein.
● Please consult our sales representative or NISSEI regional offices before designing a mold.
● Actual plasticizing capacity may vary, depending on the molding conditions and material used.